Show simple item record

dc.contributor.authorDu, Sijun
dc.date.accessioned2018-01-09T09:50:28Z
dc.date.available2018-01-09T09:50:28Z
dc.date.issued2018-01-01
dc.identifier.urihttps://www.repository.cam.ac.uk/handle/1810/270359
dc.description.abstractUltra low power wireless sensors and sensor systems are of increasing interest in a variety of applications ranging from structural health monitoring to industrial process control. Electrochemical batteries have thus far remained the primary energy sources for such systems despite the finite associated lifetimes imposed due to limitations associated with energy density. However, certain applications (such as implantable biomedical electronic devices and tire pressure sensors) require the operation of sensors and sensor systems over significant periods of time, where battery usage may be impractical and add cost due to the requirement for periodic re-charging and/or replacement. In order to address this challenge and extend the operational lifetime of wireless sensors, there has been an emerging research interest on harvesting ambient vibration energy. Vibration energy harvesting is a technology that generates electrical energy from ambient kinetic energy. Despite numerous research publications in this field over the past decade, low power density and variable ambient conditions remain as the key limitations of vibration energy harvesting. In terms of the piezoelectric transducers, the open-circuit voltage is usually low, which limits its power while extracted by a full-bridge rectifier. In terms of the interface circuits, most reported circuits are limited by the power efficiency, suitability to real-world vibration conditions and system volume due to large off-chip components required. The research reported in this thesis is focused on increasing power output of piezoelectric transducers and power extraction efficiency of interface circuits. There are five main chapters describing two new design topologies of piezoelectric transducers and three novel active interface circuits implemented with CMOS technology. In order to improve the power output of a piezoelectric transducer, a series connection configuration scheme is proposed, which splits the electrode of a harvester into multiple equal regions connected in series to inherently increase the open-circuit voltage generated by the harvester. This topology passively increases the rectified power while using a full-bridge rectifier. While most of piezoelectric transducers are designed with piezoelectric layers fully covered by electrodes, this thesis proposes a new electrode design topology, which maximizes the raw AC output power of a piezoelectric harvester by finding an optimal electrode coverage. In order to extract power from a piezoelectric harvester, three active interface circuits are proposed in this thesis. The first one improves the conventional SSHI (synchronized switch harvesting on inductor) by employing a startup circuitry to enable the system to start operating under much lower vibration excitation levels. The second one dynamically configures the connection of the two regions of a piezoelectric transducer to increase the operational range and output power under a variety of excitation levels. The third one is a novel SSH architecture which employs capacitors instead of inductors to perform synchronous voltage flip. This new architecture is named as SSHC (synchronized switch harvesting on capacitors) to distinguish from SSHI rectifiers and indicate its inductorless architecture.
dc.language.isoen
dc.rightsAll Rights Reserveden
dc.rights.urihttps://www.rioxx.net/licenses/all-rights-reserved/en
dc.subjectEnergy harvesting
dc.subjectPiezoelectric transducers
dc.subjectRectifiers
dc.subjectPower conditioning
dc.subjectPower conversion
dc.subjectEnergy management
dc.subjectSwitched capacitors
dc.subjectCMOS
dc.subjectAnalog circuits
dc.subjectSynchronized switch harvesting on inductor (SSHI)
dc.subjectSynchronized switch harvesting on capacitors (SSHC)
dc.subjectKinetic energy
dc.subjectFully integrated
dc.subjectHigh efficiency
dc.subjectInductorless
dc.subjectAC-DC converter
dc.subjectUltralow power
dc.subjectMaximum power point (MPP)
dc.subjectIntegrated circuits
dc.subjectMicroelectromechanical systems (MEMS)
dc.subjectCold startup
dc.subjectWireless sensor networks
dc.subjectInternet of Things (IoT)
dc.titleEnergy-efficient Interfaces for Vibration Energy Harvesting
dc.typeThesis
dc.type.qualificationlevelDoctoral
dc.type.qualificationnameDoctor of Philosophy (PhD)
dc.publisher.institutionUniversity of Cambridge
dc.publisher.departmentDepartment of Engineering
dc.date.updated2018-01-09T07:09:52Z
dc.identifier.doi10.17863/CAM.17227
dc.contributor.orcidDu, Sijun [0000-0001-6238-4423]
dc.publisher.collegeQueens' College
dc.type.qualificationtitlePhD in Engineering
cam.supervisorSeshia, Ashwin A.
rioxxterms.freetoread.startdate2018-01-09


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record