Show simple item record

dc.contributor.authorRoper, David
dc.contributor.authorKwon, Kyung
dc.contributor.authorMalone, Luke
dc.contributor.authorBest, Serena
dc.contributor.authorCameron, Ruth
dc.date.accessioned2022-05-30T13:10:14Z
dc.date.available2022-05-30T13:10:14Z
dc.identifier.urihttps://www.repository.cam.ac.uk/handle/1810/337601
dc.descriptionSupporting data for relevant figures within Induced Birefringence in 3D Printing: Concealing Information Optically Within Printed Objects. The deposited files contain the raw data, specifically measurements of thickness and retardation, used to calculate the birefringence values reported in Figures 2,3,4 and 7. Print speed is as defined in the GCODE for each print, given in mm min-1. The extrusion factor is defined as the ratio of material extruded to print length (see manuscript for further details). The layer separation is defined as the programmed PLLA layer height defined in the GCODE script. Thickness values are reported in m and were measured using light microscopy under 10x zoom. Each printed line was cut to produce three small (approximately 3mm in length) samples. Samples were mounted onto card and orientated perpendicular to the lens to find the sample thickness. Retardation measurements were collected by eye in transmission mode using white light with a polarised light petrological microscope, with an inserted Ehringhaus compensator. Samples were taped to a glass microscope slide, and the compensator was rotated until extinction was observed. The value on the compensator was compared to a look up table provided by Zeiss. For each print condition, retardation data was collected, as with the thickness values, from three approximately evenly spaced points along the length of the sample. The birefringence values are calculated by dividing the retardation, given in m, by the thickness, given in m. The standard deviation of the thickness and retardation were used to find the reported error values.
dc.description.sponsorshipThis work was supported by Engineering and Physical Sciences Research Council (EP/M508007/1, EP/N509620/1 and EP/N019938/1) and “Fast Assessment and Treatment in Healthcare” (FAST Healthcare) (EP/N027000/1).
dc.formatExcel
dc.rightsAttribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)
dc.rights.urihttps://creativecommons.org/licenses/by-nc-sa/4.0/
dc.subject3D printing
dc.subjectBirefringence
dc.subjectPolymer science
dc.titleSupporting data for: "Induced Birefringence in 3D Printing: Concealing Information Optically Within Printed Objects"
dc.typeDataset
dc.publisher.departmentDepartment of Materials Science And Metallurgy Student
dc.date.updated2022-03-09T15:04:14Z
dc.identifier.doi10.17863/CAM.82239
rioxxterms.licenseref.urihttps://creativecommons.org/licenses/by-nc-sa/4.0/
datacite.contributor.supervisorCameron, Ruth
dcterms.format.xls
dc.contributor.orcidCameron, Ruth [0000-0003-1573-4923]
rioxxterms.typeOther
datacite.issupplementto.doi10.1002/admt.202200139
datacite.issupplementto.urlhttps://www.repository.cam.ac.uk/handle/1810/335749
cam.depositDate2022-03-09
pubs.licence-identifierapollo-deposit-licence-2-1
pubs.licence-display-nameApollo Repository Deposit Licence Agreement
datacite.isderivedfrom.doi10.1002/admt.202200139


Files in this item

Thumbnail
Thumbnail
Thumbnail
Thumbnail

This item appears in the following Collection(s)

Show simple item record

Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)
Except where otherwise noted, this item's licence is described as Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)